Southbend SB1052F Manuel d'utilisateur Page 3
- Page / 136
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Model SB1052F
Page 2 of 3
Main Specifications
Operation Info
Swing Over Bed.................................................................................................................................. 14.17 in.
Distance Between Centers...................................................................................................................... 30 in.
Max Weight Between Centers.............................................................................................................
440 lbs.
Swing Over Cross Slide........................................................................................................................
8.66 in.
Swing Over Saddle............................................................................................................................ 13-3/4 in.
Swing Over Gap.................................................................................................................................. 20.94 in.
Maximum Tool Bit Size.......................................................................................................................... 3/4 in.
Compound Travel......................................................................................................................................
4 in.
Carriage Travel..................................................................................................................................
36-1/2 in.
Cross Slide Travel...................................................................................................................................... 7 in.
Headstock Info
Spindle Bore.......................................................................................................................................... 1.57 in.
Spindle Taper.......................................................................................................................................... MT#5
Number of Spindle Speeds............................................................................................................................
16
Spindle Speeds.........................................................................................................................
50 – 2570 RPM
Spindle Type.............................................................................................................................. D1-5 Camlock
Spindle Bearings............................................................................................................. NTN Tapered Roller
Spindle Length.................................................................................................................................. 20-7/8 in.
Spindle Length with 3-Jaw Chuck.........................................................................................................
27 in.
Spindle Length with 4-Jaw Chuck.................................................................................................
25-7/16 in.
Spindle Length with Faceplate......................................................................................................... 22-1/2 in.
Tailstock Info
Tailstock Quill Travel.......................................................................................................................... 4-3/8 in.
Tailstock Taper........................................................................................................................................ MT#3
Tailstock Barrel Diameter..................................................................................................................
1.968 in.
Threading Info
Number of Longitudinal Feeds.....................................................................................................................
17
Range of Longitudinal Feeds......................................................................................... 0.002 – 0.067 in./rev.
Number of Cross Feeds................................................................................................................................. 17
Range of Cross Feeds..................................................................................................... 0.001 – 0.034 in./rev.
Number of Inch Threads...............................................................................................................................
45
Range of Inch Threads.....................................................................................................................
2 – 72 TPI
Number of Metric Threads........................................................................................................................... 39
Range of Metric Threads........................................................................................................... 0.2 – 14.0 mm
Number of Modular Pitches.......................................................................................................................... 18
Range of Modular Pitches............................................................................................................
0.3 – 3.5 MP
Number of Diametral Pitches.......................................................................................................................
21
Range of Diametral Pitches.............................................................................................................. 8 – 44 DP
Dimensions
Bed Width.................................................................................................................................................. 9 in.
Carriage Leadscrew Diameter............................................................................................................ 1-1/8 in.
Leadscrew TPI.........................................................................................................................................
4 TPI
Carriage Leadscrew Length....................................................................................................................
59 in.
Steady Rest Capacity............................................................................................................. 5/16 – 4-5/16 in.
Follow Rest Capacity.................................................................................................................. 5/8 – 3-1/8 in.
Faceplate Size.......................................................................................................................................... 10 in.
Feed Rod Diameter.................................................................................................................................
3/4 in.
Floor to Center Height......................................................................................................................
42-5/8 in.
Height With Leveling Jacks.............................................................................................................. 54-3/8 in.
Mfd. Since 12/13 Model SB1052F
-3-
MANUAL INSERT
- MODEL SB1052F TURN-X 1
- Model SB1052F 2
- MANUAL INSERT 3
- TOOLROOM LATHE 5
- Customer Service 6
- Scope of Manual 6
- Manual Feedback 6
- Table of Contents 7
- About This Machine 9
- General Identification 10
- Controls & 11
- Components 11
- Control Panel 12
- Carriage 12
- Safety Foot Brake 13
- Product Specifications 14
- INTRODUCTION 15
- Basic Machine Safety 18
- Additional Metal Lathe Safety 20
- Additional Chuck Safety 21
- PREPARATION 22
- Power Supply 23
- Requirements 23
- Unpacking 25
- Inventory 25
- Cleaning & Protecting 26
- Location 27
- Lifting & Moving 28
- Leveling & Mounting 29
- Assembly 30
- Lubricating Lathe 30
- Adding Coolant 31
- Test Run 32
- Spindle Break-In 36
- Recommended 36
- Adjustments 36
- Operation Overview 37
- Chuck & Faceplate 38
- Mounting 38
- Installation & Removal 38
- Chuck Installation 39
- Chuck Removal 40
- Scroll Chuck Clamping 41
- 4-Jaw Chuck 41
- Faceplate 42
- Installing Tooling 44
- Removing Tooling 45
- Offsetting Tailstock 45
- Centerline 46
- Dead Centers 47
- Live Centers 48
- Mounting Center in Tailstock 48
- Removing Center from Spindle 48
- Mounting Workpiece Between 49
- Steady Rest 50
- Follow Rest 51
- Carriage & Slide Locks 51
- Four-Way Tool Post 52
- Compound Rest 52
- Micrometer Stop 54
- Adjustable Feed Stop 54
- Manual Feed 55
- Spindle Speed 55
- Setting Spindle Speed 56
- Configuration Examples 56
- Power Feed 57
- Power Feed Controls 58
- Setting Power Feed Rate 59
- Alternate Configuration 61
- Threading 62
- Apron Threading Controls 63
- Thread Dial 63
- Thread Dial Chart 64
- Chip Drawer 65
- Coolant System 66
- ACCESSORIES 68
- Maintenance Schedule 70
- South Bend Lathe Co 71
- Lubrication 72
- Quick-Change Gearbox 73
- One-Shot Oiler 74
- Longitudinal Leadscrew 74
- Ball Oilers & Oil Cup 75
- Adding Fluid 78
- Changing Coolant 78
- Machine Storage 79
- Backlash Adjustment 80
- Gib Adjustment 81
- Leadscrew End Play 81
- Adjustment 81
- Screw (1 of 2) 82
- Half Nut Adjustment 83
- Brake & Switch 84
- Leadscrew Shear Pin 86
- Replacement 86
- Gap Insert Removal & 88
- Installation 88
- Gap Installation 89
- TROUBLESHOOTING 90
- WIRING DIAGRAM COLOR KEY 93
- Wiring Overview 94
- Component Location Index 95
- Electrical Cabinet Wiring 96
- Electrical Box 97
- Spindle Motor 98
- Cutting Fluid Pump Wiring 98
- 2-Speed Motor Switch 99
- Control Panel Wiring 100
- Spindle Switches 100
- Additional Component Wiring 101
- Power Connection 101
- Headstock Cover 102
- Headstock Controls 103
- Headstock Controls Parts List 104
- Headstock Internal Gears 105
- For Machines Mfg. Since 5/11 106
- 14" TURN-X 106
- Toolroom Lathe 106
- Headstock Transfer Gears 107
- Gearbox Gears 108
- Gearbox Gears Parts List 109
- Gearbox Controls 110
- Gearbox Controls Parts List 111
- Apron Front View 112
- Apron Front View Parts List 113
- Apron Rear View 114
- Apron Rear View Parts List 115
- Compound Rest & Tool Post 116
- Saddle Top View 117
- Saddle Top View Parts List 118
- Saddle Bottom View 119
- Bed Stop 120
- Dial Indicator 120
- Bed & Shafts 121
- Bed & Shafts Parts List 122
- End Gears 123
- Main Motor 124
- Main Motor Parts List 125
- Stands & Panels 126
- Tailstock 128
- Tailstock Parts List 129
- Steady Rest Follow Rest 130
- Accessories 132
- Front Machine Labels 133
- Warranty 135
- Printed In U.S.A. #TS14364 136
Produits connexes et manuels pour Tours Southbend SB1052F
Tours Southbend SB1224 Manuel d'utilisateur
(12 pages)
(12 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.200 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels